Technical (Moderators: volkenstein, 68autobug)

netral start switch

Started by 007kilmer

Replies: 2
Views: 1,586

17 September 2008, 14:15
by volkenstein

Where are these located in the car?

Started by 007kilmer

Replies: 3
Views: 1,812

08 September 2008, 14:27
by 68autobug

Stalling in reverse

Started by 1970 conv AS

Replies: 2
Views: 2,354

05 August 2007, 06:47
by 68autobug

Transmission plate bolt size, M7/1.25?

Started by 1972autostick

Replies: 1
Views: 505

24 December 2023, 22:07
by 1972autostick

Flex/Drive plate warping and shim question

Started by 1972autostick

Replies: 1
Views: 325

24 December 2023, 22:05
by 1972autostick

Popping out of 1st gear

Started by 2rightfeet

Replies: 9
Views: 3,708

16 April 2015, 04:22
by 68autobug

Neutral Safety Switch

Started by 55chib

Replies: 2
Views: 1,873

15 October 2008, 03:22
by 55chib

73 Super Beetle Autostick engine rebuild questions

Started by 67beetledude

Replies: 8
Views: 4,497

10 July 2008, 04:32
by Bookwus

1973 Super Beetle Shift Interlock Switch

Started by 67vetteal

Replies: 9
Views: 2,765

28 July 2017, 09:49
by 68autobug

68 autostick pops out of gear

Started by 68asMA

Replies: 1
Views: 1,279

06 August 2012, 13:52
by 68autobug

The gasket in the ATF dipstick CAP was needed - found the oil cap gasket fits

Started by 68autobug

Replies: 1
Views: 1,413

06 December 2013, 22:43
by CarlIseminger

How do You replace the input shaft seal in the tube in the bell housing?

Started by 68autobug

Replies: 3
Views: 2,523

29 July 2007, 10:14
by 68autobug

I received a PM from Tina tc13m who has a 1302 with an ATF leak.

Started by 68autobug

Replies: 0
Views: 1,092

04 June 2017, 09:17
by 68autobug

I will get My gears and crunching sorted out - THIS YEAR...FIXED-FIXED

Started by 68autobug

Replies: 2
Views: 2,053

16 August 2008, 15:26
by Bookwus

anyone know what cap fits a Bosch 050 or 010 Distributor??

Started by 68autobug

Replies: 2
Views: 2,113

10 July 2010, 02:59
by volkenstein

Engine and Gearbox out.... replacing the gearbox... Jan 2008

Started by 68autobug

Replies: 6
Views: 2,694

05 February 2008, 07:38
by 68autobug

Hard to get out of gear....

Started by 68autobug

Replies: 0
Views: 1,522

01 May 2012, 14:53
by 68autobug

Who has stripped a sump plate thread or nut when changing the oil??

Started by 68autobug

Replies: 8
Views: 2,814

24 April 2008, 16:57
by 68autobug

I took My clutch servo off today... wasn't all that difficult... one handed..

Started by 68autobug

Replies: 5
Views: 2,286

16 May 2008, 16:30
by 68autobug

Wiring Modifications - New SVDA has arrived -

Started by 68autobug

Replies: 9
Views: 3,015

03 November 2009, 10:33
by 68autobug